Flooring insight
Flooring Orders Checklist: 7 Steps I Use Before Every Karndean, Underlayment, or Coating Purchase
-
Who This Checklist Is For
-
Step 1: Confirm the Installation Method Before You Order Anything
-
Step 2: Get Underlayment Compatibility in Writing — Not in a Brochure
-
Step 3: Order a Sample and Test It — Before Bulk
-
Step 4: Force the Full Cost Breakdown Into the Quote
-
Step 5: For Architectural Coating at Wholesale — Verify VOC and Certifications First
-
Step 6: Lock Down Delivery Terms and Damage Policy in Writing
-
Step 7: The 24-Hour Pre-Shipment Confirmation (Most People Skip This)
-
Common Mistakes to Watch For
Who This Checklist Is For
If you're placing LVT orders, sourcing underlayment from an OEM supplier, or picking architectural coating for wholesale, this is for you. Seven steps. No theory.
I've been handling B2B flooring orders for six years. Karndean lines mostly, but also underlayment from three different OEM vendors and coatings from four wholesale suppliers. Over that time I've documented roughly $4,700 in mistakes that were 100% preventable. This checklist is what came out of it.
Two things to know upfront: prices and specs move fast in this industry, so verify anything I mention today. And my experience is domestic-focused, mid-to-high-volume B2B orders. If you're doing small-batch imports or ultra-budget retail, your mileage will differ.
Step 1: Confirm the Installation Method Before You Order Anything
This sounds obvious. It isn't. Karndean carries multiple lines, and the installation method changes the whole order — adhesive, subfloor prep, acclimation, everything.
Karndean Knight Tile glue down is a different animal from a click-lock plank. With glue-down, you need the right adhesive, a properly primed subfloor, and an installer who's actually done it before. With click, you need the opposite — a level subfloor without glue, minimal prep, faster install.
In early 2021 I quoted a project using Knight Tile on the assumption our installer would glue it. He showed up expecting a click install. Not his fault — I never put it in writing. Cost us a week of delay and $1,100 in extra labor while we sorted out the adhesive and re-prepped the floor.
Your check: Write the installation method into the purchase order itself. Not a separate email. The PO.
Step 2: Get Underlayment Compatibility in Writing — Not in a Brochure
Floor underlayment OEM suppliers are the wild west. Half the spec sheets I've received are marketing documents pretending to be technical ones.
The problem: a supplier says their underlayment "works with luxury vinyl." Okay. But does it work with glue-down luxury vinyl at 2.5mm wear layer, in a space with humidity swings, over a concrete slab? The brochure won't tell you.
I only started demanding technical data sheets after spending $800 on an underlayment that voided the Karndean warranty. Never got the money back. Never even got an acknowledgment that the incompatibility existed, because the only thing I had was a sales rep saying "yeah, it'll be fine."
Your check: For every underlayment order, request:
- Full technical data sheet (not a sell sheet)
- Written compatibility statement for your specific flooring product and installation method
- Acoustic rating, compression resistance, and moisture barrier specs if applicable
- Confirmation that using it won't void your flooring manufacturer's warranty
If the OEM rep can't provide all four, walk. There's another supplier two clicks away.
Step 3: Order a Sample and Test It — Before Bulk
The single most-skipped step by B2B buyers. You see a photo, you see a spec sheet, you order 20,000 sq ft. Then it arrives and the color is two shades off from the sample you were shown, or the emboss pattern doesn't match the display in your showroom.
Karndean's design consistency is actually good across batches — that's one of the reasons we stock them. But "good" isn't "identical," and lighting conditions in your facility aren't the same as the showroom where you picked the design.
We keep a physical sample board in the warehouse for every Karndean line we stock. Before any bulk order over 5,000 sq ft, the warehouse manager pulls the board and compares it to the current batch sample sent by the distributor. Takes ten minutes. Has caught three color discrepancies in two years.
Your check: Physical sample in your actual lighting. Not on a screen.
Step 4: Force the Full Cost Breakdown Into the Quote
Here's my honest opinion, earned the hard way: transparent pricing beats clever pricing. Every time.
I've been on both sides of this. Early on, I'd take the lowest quote and figure out the extras later. Setup fees, freight surcharges, minimum order adjustments, pallet deposits, rush fees — none of them in the original number. One project ended up 34% over the "quoted" price by the time the invoice landed.
Now I ask the question in the other order. Not "what's the price" but "what's not included in this price."
A vendor who lists everything upfront — even if the total looks higher at first glance — usually costs less in the end. Because there's no surprise round. No re-approval. No CFO asking why the number changed.
Your check: Every quote you accept should include:
- Unit price and total product cost
- Freight — actual number, not "TBD"
- Any setup, handling, or minimum-order charges
- Payment terms and whether a card or wire fee applies
- Return/restock policy for excess material
If a vendor won't itemize this, they're either disorganized or counting on you not noticing. Either way, not your problem to solve.
Step 5: For Architectural Coating at Wholesale — Verify VOC and Certifications First
Choosing architectural coating for wholesale is where I've seen the most quiet damage happen. Nobody notices a coating problem on day one. It shows up six months later when the surface yellows, or peels at the seams, or fails an inspection.
Two things I always verify before any wholesale coating order:
VOC content and regulatory compliance. Get the actual g/L number and confirm it against your target region's requirements. "Low VOC" is a marketing term. The number is the fact. Ask for the SDS, not the summary.
Certification claims. If a supplier claims a coating meets a certain standard, ask for the test report or the certificate number. If they can't produce it, the claim is decoration.
The time-bound caveat here: VOC regulations in several U.S. states have tightened since 2023, and they'll keep tightening. Anything you verified two years ago should be re-verified today.
Step 6: Lock Down Delivery Terms and Damage Policy in Writing
Flooring is heavy, bulky, and gets handled a lot before it lands on your dock. Damage happens. The question is who pays for it.
Some distributors inspect pallets before shipping and document condition. Some don't. Some will replace damaged material at no cost if you report within 48 hours. Some will fight you for three weeks over a $600 claim.
We got burned in 2022 by a distributor with no written damage policy. A pallet of Karndean arrived with water-damaged corners on eleven boxes. Their position: "that's a carrier issue." The carrier's position: "that's a loading issue." We ate $740.
Your check: Before your first order with any distributor, ask:
- What's the damage reporting window?
- Who files the freight claim — you or them?
- What's the process for replacement material if claims take weeks?
Get the answer in email. Keep the email.
Step 7: The 24-Hour Pre-Shipment Confirmation (Most People Skip This)
This is the one nobody does. I didn't do it for three years.
Twenty-four hours before your order ships, call or email the distributor and confirm: product line, quantity, batch number if available, shipping address, delivery date, and the name of whoever's signing for it.
Takes five minutes. Has caught four errors in eighteen months — wrong quantity twice, wrong line once, wrong ship-to once. Each one would've cost between $300 and $1,500 to fix after the fact.
Written POs help. This step closes the last gap between what's on the PO and what's actually on the truck.
Common Mistakes to Watch For
A few things that keep showing up, even with experienced buyers:
- Assuming all LVT is the same. Installation method, wear layer, backing — they vary. Match the product to the application, not the other way around.
- Trusting a verbal spec. If it matters, it needs to be on paper. Every warranty claim I've filed that failed was because the spec was verbal.
- Skipping the sample board. Photos lie. Lighting lies. Physical samples in your facility don't.
- Buying on price alone. The cheapest quote plus hidden fees often costs more than the upfront-transparent one.
- Forgetting to verify OEM compatibility. A $200 savings on underlayment can cost a $2,000 warranty claim.
None of these are genius insights. They're just things I learned the expensive way, and I'd rather you didn't.
Pricing and regulatory details referenced here reflect conditions as of early 2025. Verify current specs, fees, and compliance requirements before placing orders — this market moves faster than most people expect.