Flooring insight
I Specified Karndean Flooring for Our Office. Here’s What Almost Went Very Wrong.
In 2023, I was asked to pick flooring for our company’s office expansion. Two buildings, roughly 40,000 square feet combined. 400+ employees walking on this every single day. I did what most people do: I looked at samples. I compared Karndean design series against each other, debated wood-look versus stone-look, and got executive approval on aesthetics.
I thought the hard part was choosing the product. Turns out that was the easy part.
If you’re in the middle of a similar project—maybe you’re buried in ceramic tile specifications and wondering why they don’t quite fit your vinyl plan—this is for you. I’m going to walk through what actually caused our problems. Not the obvious stuff. The stuff underneath.
The Problem I Thought I Had
On paper, everything looked right. Karndean flooring is an established luxury vinyl tile brand with a substantial design catalog. We wanted a natural wood look that would survive open-office traffic, and the product line checked that box. Price was defensible for a spec-grade product. Installation was scheduled. I placed the purchase order feeling fairly confident.
That confidence lasted about three weeks.
The Real Problem: It Was Never About the Surface
Three different issues surfaced during the project, and none of them came from the tile itself. They came from the conditions around it. If I had known then what I know now, we would have avoided nearly every single delay.
1. The Subfloor Had a Vote
Nobody asked about the concrete slab until the general contractor casually mentioned moisture testing. Let me back up. In glue-down LVT installations, the subfloor’s moisture content is a deciding factor in how the adhesive performs. Ceramic tile can tolerate some dampness and unevenness because it’s rigid and set in mortar. Vinyl can’t. It’s thin and flexible, which means it telegraphs every imperfection below it.
Karndean’s installation guidelines (karndean.com) are explicit: subfloor testing is required for glue-down installations. It’s not a complicated test—a calcium chloride or relative humidity test takes a few days. Nobody had scheduled it. We ran the test late, got a borderline reading, and had to apply a moisture mitigation membrane. That added three weeks to the schedule and roughly $12,000 in work.
What frustrates me in hindsight: none of this showed up in the original project spec. The drawings mentioned finished floor coverings. The conditions underneath were treated as a mystery box.
2. The Adhesive Nearly Sunk the Whole Thing
This one scares me in hindsight. When I asked the installer what adhesive he planned to use, he said he’d “use my usual stuff.” His usual stuff was a generic pressure-sensitive adhesive that was not approved for this product system. Karndean adhesive is formulated for Karndean products—different open time, moisture tolerance, and bond strength. Mixing in unapproved adhesive voids the warranty and drastically raises the risk of bond failure.
I pushed back. The installer, to be fair, wasn’t trying to cut corners. He genuinely didn’t know that LVT adhesives are product-specific to that degree. But if I’d let it slide, we would have had floating spots and visible seams within the first winter. Try explaining that to your VP after the project is already over budget.
Why did I almost make this mistake? Because I let the person doing the work make the material decision. That’s on me. In my first renovation I made the classic rookie error: assuming adhesive was adhesive. It’s not. The same principle applies across categories. Whether it’s Karndean adhesive, primer, or an industrial sealant for a wholesale job, the questions are identical: What did the manufacturer specify? What does the warranty allow? What happens if we substitute? If you’re at the point of searching “how to choose industrial sealant for wholesale,” the answer starts with the spec sheet—not the price sheet.
3. The Ceramic Tile Specification Trap
Here’s the subtle problem that might be sitting on your desk right now. A lot of architectural drawings default to ceramic tile specifications for commercial flooring. That’s fine when you’re actually installing tile. We weren’t. Our project had LVT in three of five main zones, but the spec still called out tile tolerances, tile flatness requirements, and tile moisture assumptions.
Why does this matter? Because ceramic tile specifications and LVT specifications are different documents for different systems. A tile spec might allow a subfloor flatness tolerance of 1/4” over 10 feet. LVT demands tighter. A tile spec might assume the installer works from “level enough.” LVT requires a substrate that’s been leveled and smoothed. On paper, those differences look small. In a real project, they’re the difference between a clean install and a calendar full of change orders.
If you’re holding a set of ceramic tile specifications but the project actually calls for vinyl flooring, get the drawings revised before anyone orders material. And when comparing vinyl flooring manufacturer claims, pay attention to the detail of the installation manual. The manufacturers who document their requirements carefully are the ones who’ll stand behind the product.
What It Cost Us
Total impact: about six weeks of combined schedule delay, plus $18,000 in unplanned mitigation and corrective work. The budget had been approved the previous fall. Two change orders meant two rounds of finance review, which meant two emails to my VP explaining why the original number was wrong. Not a fun conversation.
And honestly? We got lucky. The subfloor got fixed. The adhesive was corrected before install. But if I’d let that unapproved glue go down, the failure would have been invisible for months. Then the ripples would start under the vinyl. Then the seams would lift. Then the real conversation with the manufacturer would begin with, “Let me see your installation records.”
Bond failure rarely looks dramatic. It just quietly destroys the floor you signed off on.
Here’s the part that keeps me up at night: the people walking on that floor had no idea any of this was happening. The failure was silent until it wasn’t.
The Fix Was Not Exciting
If you want the short version, here’s what I’d tell any buyer working on a Karndean project—or honestly, any LVT project:
- Verify the subfloor before you order. Test for moisture and flatness. Ask for the reports. If the numbers are marginal, build remediation into the schedule and budget before the material arrives.
- Use the manufacturer’s adhesive system. If the installation guide says Karndean adhesive, that’s what goes into the purchase order. No substitutions. Period.
- Check the drawings for the “tile” problem. If the spec says “tile” but the project is LVT, ask for a revision. Make the paperwork match reality.
- Read the warranty conditions front to back. Warranty documents tell you exactly what’s allowed. Follow them literally.
If you’re sourcing at volume, the same discipline applies to every chemical component—adhesive, primer, transition adhesive, industrial sealant. The SKU on the purchase order should match the manufacturer’s specification. Nothing less.
When Karndean Isn’t the Right Call
I also want to say the honest thing: Karndean isn’t the right answer for every space. If you’re flooring a commercial kitchen or any area with standing water, glue-down vinyl has real limits. If your concrete slab has persistent moisture problems that remediation can’t fix, you should look at a different system entirely. If your facility is an industrial warehouse with fork trucks running over the surface all day, LVT is probably too vulnerable for that environment.
Knowing when a product isn’t right for the job is part of the job. I’m more convinced of that now than I was in 2023. When a vendor asks enough questions to talk you out of a product that doesn’t fit your situation, that’s a good sign—not a red flag.
For our office—moderate foot traffic, design-conscious stakeholders, stable subfloor after remediation—Karndean flooring made sense. The design range impressed our team. The cost was reasonable for the quality. And once we dealt with everything below the surface, the finished space genuinely looked great.
But I’ll never again pick a flooring product by staring at samples alone. The important decisions happen under the floor, in the specs, and on the substrate. That’s where the project is won.