Flooring insight

Why We Switched to Karndean LVT Flooring After a $19,000 Tile Mistake

2026-08-26 · Emilia Novak

When I took over purchasing for our company in 2021, I learned quickly that "cheaper per unit" is a trap. But I didn't learn it from office supplies. I learned it from flooring.

In early 2024, we planned a renovation for our 4,200-square-foot office in Portland: three work areas, a couple of conference rooms, and the reception entrance. I managed all of it—ordering materials, coordinating the contractor, reporting to operations and finance.

The first question from our CFO was predictable: "Which flooring is cheaper?"

I ran the numbers in February 2024. Porcelain tile: $4.20 per square foot. Karndean LVT flooring: $4.85 per square foot. The tile won. We ordered it.

That decision cost us about $19,000 more than the original estimate. Not an exaggeration. I have the budget spreadsheet open while I'm writing this.

The surface problem: comparing the wrong number

Most buyers focus on per-square-foot pricing and completely miss everything wrapped around it. I was exactly that buyer.

I compared material costs, got installation quotes from two contractors, and made a decision. What I didn't do was read the porcelain tile specifications. That spec sheet turned out to be the most expensive document I ignored all year.

Here's what the tile spec required that we hadn't planned for:

  • Substrate flatness: The slab had to be flat within 1/8" over 10 feet. Our 1980s building wasn't. Self-leveling compound across the entire floor: $4,200 we hadn't budgeted.
  • Moisture testing: A calcium chloride test—72 hours minimum, just to wait for results. The first test came back at 4.5 lbs, above the tile manufacturer's 3 lbs limit. Add a vapor barrier and another $2,100.
  • Expansion joints: Nobody mentioned these until the supplier's technical rep flagged our layout. The wall-to-window span required expansion joint systems: $1,600.

(If you've specified tile before, you're nodding. If you haven't, that's exactly the point—none of this appears in a per-foot tile quote.)

The deeper problem: underlayment and compliance

While I was sorting out the tile issues, I made two more mistakes. I can laugh about them now. Barely.

The contractor recommended a floor underlayment private label product. Cheaper than the brand-name option, and honestly, the packaging looked similar. I approved it without reading the technical data sheet. That's not like me. But I was stretched thin, so I signed off.

Here's the thing about private label underlayment: it isn't universal. The tile manufacturer's installation guidelines specified a minimum compressive strength. The private label product didn't publish that number. Not because it was secret—because it hadn't been tested.

When the tile manufacturer's rep came for a site inspection (required for warranty validation), he caught it. The underlayment had to be replaced before any tile went down. Another week lost, another $2,400 out of pocket.

Then came the adhesive problem.

Our original adhesive supplier couldn't provide the industrial sealant compliance requirements documentation we needed. Our building requires low-VOC products, and we were tracking LEED points. The supplier had screenshots of a spec sheet. Screenshots aren't compliance documentation. Our installer refused to use the adhesive without the third-party test report. Good on him, honestly.

If it isn't documented, it didn't happen. In commercial construction, that rule will save you.

That delay cost us 10 business days. Our temporary workspace was $3,600 a month, so the delay effectively cost about $1,700. Plus the awkward conversations with my operations director about why we were paying for a space we couldn't occupy.

The real cost: money, time, and perception

Here's the honest total:

  • Original tile material quote: $17,900
  • Self-leveling compound: $4,200
  • Moisture testing and vapor barrier: $2,100
  • Expansion joints: $1,600
  • Replacement underlayment: $2,400
  • Compliance delay and temp space: $3,200
  • Contractor labor overage: $5,800

Total additional: about $19,300 on a project we chose because it saved $2,700 up front.

But the dollars weren't the worst part. The worst part was how it looked when clients visited.

We'd finished the reception area but not the conference rooms. The underlayment replacement had left a visible patch under the tile. Grout lines in one corner were still open—the installer was waiting on the expansion joint material. In a space where we sit prospects, we looked like a construction site.

Our CEO didn't say anything. He didn't have to. The VP who walked the client through later told me the prospect asked: "Is this space still under construction?" That's not the impression you want when you're pitching an office experience.

This is where the quality perception lesson lands for me: clients can't tell whether you specified your flooring through rigorous cost analysis or by picking the cheapest catalog listing. They see what's in front of them. And a floor with patches and unfinished edges quietly says "this company doesn't sweat the details." Once they think that, everything else you pitch gets filtered through it.

People think premium products cost more because of marketing budgets. Actually, products that meet spec cost more because the engineering, testing, and documentation behind them cost more. The causation runs the other way.

What we should have done first: Karndean LVT flooring

We eventually pulled out the reception tile and replaced it. Yes, we had to rip out the tile we'd just installed. Yes, that hurt.

What went in was Karndean LVT flooring, and I'll be straightforward: I initially resisted the quote because it was about $0.65 per square foot more than the tile. I'll never make that mistake again.

The first difference wasn't the look—it was the paperwork. Karndean's technical documentation was complete and upfront. No maze of referenced standards. The porcelain tile specifications had been a multi-day research project. Karndean's spec data was direct: subfloor requirements, installation methods, adhesive requirements, all in one place.

We used the Korlok click system for most of the space, which eliminated the adhesive question entirely. The glue-down areas (conference rooms, a specific stone design we liked) used a Karndean-recommended adhesive that came with its compliance documentation ready: VOC test reports, SCAQMD Rule 1168 compliance, all the paperwork our building manager wanted. No back-and-forth.

About private label again, because I know it's tempting. Floor underlayment private label products can be perfectly good—but only if you verify them against the flooring manufacturer's written requirements. We used a Karndean-recommended underlayment this time. It cost a few cents more per square foot. Trivial, compared to the $2,400 lesson we'd just paid.

And the design realism genuinely surprised me. I'm an office administrator, not a designer. I expected "vinyl" to look like vinyl. The Karndean Design Series wood and stone visuals were noticeably better than that. The reception area uses a marble look from the Art Select collection, and I've had two visitors ask if it's real stone. One asked if it was polished concrete. The point is: nobody guessed it was LVT. Not once.

We also saved time on installation. The Korlok click system went down in about a third of the time the tile install had taken. Our contractor estimated the full floor would have taken around five days with the click system, versus nearly three weeks for the tile with all its prep work.

Eight months later

As of January 2025, the Karndean flooring has been down for about eight months. Maintenance is simpler than the tile schedule would have demanded—no grout lines, no sealing cycle. The maintenance contractor actually said the stripping cycle is running longer than they'd budgeted for.

There's something satisfying about a floor that simply works. After the failed moisture tests, the underlayment fiasco, the compliance delays—having a floor that looks professional and cleans up in one pass is a quiet win. I'll take it.

If you're in the middle of a similar decision right now, here's what I'd do differently:

  1. Compare total specified cost, not unit price. Read the spec sheets first, then add substrate prep, underlayment, adhesives, and compliance documentation into the comparison.
  2. Verify underlayment compatibility against the flooring manufacturer's published requirements. Don't assume a private label product is identical to the name-brand equivalent.
  3. Ask for compliance documentation before you order, not after. One email to the manufacturer can save a two-week delay later.

Porcelain tile is a fine material, if you ask me. I won't tell anyone to avoid it—it genuinely works well in many commercial spaces. But I'll never specify it again without reading the full specifications first. And I'll never choose flooring on unit price alone.

Some lessons are expensive. This one cost us $19,000. If this article saves you that same tuition, it was worth writing.

Emilia Novak
Emilia Novak

Emilia Novak is a flooring and architectural-surfaces analyst covering ceramic and porcelain tile, natural stone, resilient flooring, underlayments, countertops, adhesives, grout, and installation accessories. She uses ASTM C373 and ASTM C648 test evidence while comparing water absorption, breaking strength, slab flatness, substrate moisture, joint width, slip resistance, and installed tolerances. Her specification guides help architects, contractors, and buyers match surface systems to traffic, wet-area exposure, maintenance demands, and substrate conditions.